JDM MAINTENANCE -- #702 CONCRETE CURE SEAL HARDENER  -- 8030-00N025754
<pre>=====================  Product Identification  =====================

Product ID:#702 CONCRETE CURE SEAL HARDENER
MSDS Date:05/01/1990
FSC:8030
NIIN:00N025754
MSDS Number: BMBQC
=== Responsible Party ===
Company Name:JDM MAINTENANCE
Box:379
City:COMMACK
State:NY
ZIP:11725
Country:US
Info Phone Num:516-499-0623
Emergency Phone Num:516-499-0623
CAGE:JDMMA
=== Contractor Identification ===
Company Name:JDM MAINTENANCE CORP
Box:379
City:COMMACK
State:NY
ZIP:11725
Country:US
Phone:414-354-6417
CAGE:JDMMA

=============  Composition/Information on Ingredients  =============

Ingred Name:BENZIN; (AROMATIC NAPHTHA). VP:4. LEL:1%.
CAS:8030-30-6
RTECS #:DE3030000
Fraction by Wt: 40-80%
OSHA PEL:100 PPM
ACGIH TLV:100 PPM

Ingred Name:PARAFFIN WAXES AND HYDROCARBON WAXES, CHLORINATED;
    (CHLORINATED PARAFFIN)
CAS:63449-39-8
RTECS #:RV0450000
Fraction by Wt: 1-8%

Ingred Name:SUPP DATA:SAND, CLAY, EARTH, FLOOR ABSORB/OTHER ABSORB MATL
    & SHOVELED INTO CNTNRS.
RTECS #:9999999ZZ

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES  Skin:YES  Ingestion:YES
Reports of Carcinogenicity:NTP:NO    IARC:YES	 OSHA:NO
Health Hazards Acute and Chronic:EYES:CAN CAUSE SEV IRRIT, REDNESS,
    TEARING, BLURRED VISION. SKIN:CAN CAUSE MOD IRRIT, DEFAT, DERM.
    INHAL:CAN CAUSE NAUS & HDCH, POSS UNCON & EVEN ASPHY. INGEST:CAN
    CAUSE GI IRRIT, NAUS, VOMIT & DIARR.  ASPIR OF MATL INTO LUNGS CAN
    CAUSE CHEM PNEUMOCONIOSIS WHICH CAN BE FATAL.
Explanation of Carcinogenicity:CHLOROPARAFFIN WAXES AND HYDROCARBON
    WAXES:GROUP 2B(IARC).
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

=======================  First Aid Measures  =======================

First Aid:EYES:FLUSH W/LG AMTS OF H*2O FOR @ LST 15 MIN, LIFTING UPPER
    & LOWER LIDS OCCAS. CALL MD. SKIN:THORO WASH EXPOSED AREA W/SOAP &
    H*2O. REMOVE CONTAM CLTHG. LAUNDER CONTAM CLTHG BEFORE RE-USE.
    INHAL:REM OVE INDIVIDUAL TO FRESH AIR. IF BRTHG HAS STOPPED, GIVE
    ARTF RESP. KEEP PERS WARM, QUIET & CALL MD. INGEST:DO NOT INDUCE
    VOMIT, KEEP PERS WARM, QUIET & CALL MD.

=====================  Fire Fighting Measures  =====================

Flash Point:110F,43C
Lower Limits:1%
Extinguishing Media:REGULAR FOAM, CO*2 OR DRY CHEMICAL.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED PRESSURE DEMAND SCBA
    & FULL PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:VAPS ARE HVR/AIR & MAY TRAVEL ALONG
    GROUND/MAY BE MOVED BY VENT & IGNITED BY PILOT LIGHTS, OTHER
    FLAMES, SPKS, HEATERS, SMOKING, ELEC MOTORS/OTHER IGNIT(SUPDAT)

==================  Accidental Release Measures  ==================

Spill Release Procedures:SM SPILL:ABSORB LIQ ON PAPER, VERMICULITE,
    FLOOR ABSORB/OTHER ABSORB MATL & TRANSFER TO VENTED CLOSURE. LG
    SPILL:ELIM ALL IGNIT SOURCES (FLAMES, PILOT LIGHTS, ELEC SOURCES,
    ETC). PERS NOT WEARING PROT  EQUIP SHOULD BE EXCLUDED FROM AREA OF
    (SUPP DATA)
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:CNTNRS OF THIS MATL MAY BE HAZ WHEN
    EMPTIED. KEEP OUT OF REACH OF CHILDREN.
Other Precautions:SINCE EMPTIED CNTNRS RETAIN PROD RESIDUES (VAP, LIQ
    &/OR SOLID), ALL HAZ PRECS GIVEN IN THIS MSDS MUST BE OBSERVED.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:IF TLV OF PROD IS EXCEEDED, A NIOSH/MSHA JOINTLY
    APPROVED SCBA W/FULL FACE PIECE OPERATED IN POSITIVE PRESSURE
    MODE/OTHER NIOSH/MSHA APPROVED RESPIRATORS UNDER SPECIFIED
    CONDITIONS.
Ventilation:PROVIDE SUFFICIENT MECH (GENERAL) &/OR LOCAL EXHAUST VENT
    TO MAINTAIN EXPOSURE BELOW TLV'S.
Protective Gloves:RESISTANT GLOVES LIKE BUNA-N.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:TO PREVENT REPEATED OR PROLONGED SKIN
    CONTACT WEAR IMPERVIOUS CLOTHING & BOOTS.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
EXPLO HAZ:SOURCES @ LOCATIONS DIST FROM MATL HNDLG POINT. NEVER USE
    WELDING/CUTTING TORCH ON/NEAR DRUM (EVEN EMPTY) BECAUSE PROD (EVEN
    JUST RESIDUE) CAN IGNITE EXPLOSIVELY. SPILL PROC:SPILL. STOP SPIL L
    @ SOURCE, DIKE AREA OF SPILL TO PVNT SPREADING, PUMP LIQ TO SALVAGE
    TANK. REMAINING LIQ MAY BE TAKEN UP ON (INGRED 3)

==================  Physical/Chemical Properties  ==================

HCC:F4
Boiling Pt:B.P. Text:323F,162C
Vapor Pres:SEE ING 1
Vapor Density:HVR/AIR
Spec Gravity:0.9-1.4 
Evaporation Rate &amp; Reference:SLOWER THAN ETHER
Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.
Percent Volatiles by Volume:53-82

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT W/STRONG OXIDIZING AGENTS (E.G. NITRIC ACID,
    PERMANGANATES, ETC).
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:MAY FORM TOX MATLS - CO*2 & CO, HCL,
    STYRENE & ACRYLATE MONOMERS, ETC.

====================  Disposal Considerations  ====================

Waste Disposal Methods:DISPOSE OF I/A/W LOCAL, STATE & FEDERAL
    REGULATIONS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.